Login


Nieuwe klant
Login
Winkelwagen
€ 0,00
Verzendkosten: 0,00
Totaal ex btw: 0,00
Producten

Verzending

Bestellingen tot 12.00 uur zullen wij dezelfde dag nog in behandeling nemen en verzenden.

Verzendkosten Brievenbuspost
 
Nederland
Bestelling van 0 tot 25 euro    € 2,95
boven de 25 euro                     gratis


Verzendkosten Pakketpost.

Nederland
Bestelling van 0 tot 65euro      € 5,95
boven de 65 euro                     gratis

België en Duitsland. 
Bestelling van 0 tot 65euro     € 8,50
boven de 65 euro                     gratis

 

Betaling

Het betalen van een bestelling doet u veilig en makkelijk met iDEAL, PayPal, Mister-Cash, Billink of na het bestellen per bankoverschrijving. In dat geval ontvangt u van ons een mail hoe u het bedrag kunt overmaken.
 
805XJ3v3Iw4fEmT538K2b49T00D6n332.jpg
Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070 Adafruit 1362 Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070 Adafruit 1362 Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070 Adafruit 1362 Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070 Adafruit 1362
Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070 Adafruit 1362 Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070 Adafruit 1362 Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070 Adafruit 1362 Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070 Adafruit 1362
Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070 Adafruit 1362
0 Review | Review toevoegen
Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070 Adafruit 1362

Artikelnummer

11419

Verzendkosten

€ 2,95

Verwachte levertijd

Direct uit voorraad leverbaar

€ 12,95
Prijs per stuk

Voorraad : 1

Aantal: 
Bestellen
 
Op verlanglijst

Heeft u een vraag over dit product?

Stel ons uw vraag

Standalone 5-Pad Capacitive Touch Sensor Breakout - AT42QT1070 Adafruit 1362

This breakout board is the simplest way to create a project with mutiple capacitive touch sensors. No microcontroller is required here - just power with 1.8 to 5.5VDC and connect up to 5 conductive pads to the 5 left-hand pins. When a capacitive load is detected (e.g. a person touches one of the conductive contacts) the corresponding LED on the right lights up and the output pin goes low. You can use this to update an existing normal-button project where buttons connect to ground when pressed.

Note that only one contact will be detected at once (this is to protect against having a hand brush against two or more contacts at once.

Comes with a fully assembled board, and a stick of 0.1" header so you can plug it into a breadboard. For contacts, we suggest using copper foil, then solder a wire that connects from the foil pad to the breakout.

The datasheet has many details on sensitivity, power usage, etc. - note that this board uses the chip in 'standalone' mode only, it cannot be used in I2C mode.
 

 

Voor meer info klik hier
 

Sorteren op:

Review toevoegen

Geen reviews gevonden.

Stel een vraag over dit product

Velden met een * zijn verplicht om in te vullen.

Jouw vraag is verzonden! Bedankt.

We zullen jou zo snel mogelijk voorzien van een antwoord.