Login


Nieuwe klant
Login
Winkelwagen
€ 0,00
Verzendkosten: 0,00
Totaal ex btw: 0,00
Producten

Verzending

Bestellingen tot 12.00 uur zullen wij dezelfde dag nog in behandeling nemen en verzenden.

Verzendkosten Brievenbuspost
 
Nederland
Bestelling van 0 tot 25 euro    € 2,95
boven de 25 euro                     gratis


Verzendkosten Pakketpost.

Nederland
Bestelling van 0 tot 65euro      € 5,95
boven de 65 euro                     gratis

België en Duitsland. 
Bestelling van 0 tot 65euro     € 8,50
boven de 65 euro                     gratis

 

Betaling

Het betalen van een bestelling doet u veilig en makkelijk met iDEAL, PayPal, Mister-Cash, Billink of na het bestellen per bankoverschrijving. In dat geval ontvangt u van ons een mail hoe u het bedrag kunt overmaken.
 
805XJ3v3Iw4fEmT538K2b49T00D6n332.jpg
Push-button Power Switch Breakout  Adafruit 1400 Push-button Power Switch Breakout  Adafruit 1400 Push-button Power Switch Breakout  Adafruit 1400 Push-button Power Switch Breakout  Adafruit 1400
Push-button Power Switch Breakout  Adafruit 1400 Push-button Power Switch Breakout  Adafruit 1400 Push-button Power Switch Breakout  Adafruit 1400 Push-button Power Switch Breakout  Adafruit 1400
Push-button Power Switch Breakout Adafruit 1400
0 Review | Review toevoegen
Push-button Power Switch Breakout Adafruit 1400

Artikelnummer

11715

Verzendkosten

€ 2,95

Verwachte levertijd

7 dag(en)

€ 8,95
Prijs per stuk

Voorraad : 0

Dit product is niet uit voorraad leverbaar
 
Op verlanglijst

Heeft u een vraag over dit product?

Stel ons uw vraag

Push-button Power Switch Breakout  Adafruit 1400

The Adafruit Push-button Power Switch is a tidy little design that lets you control a DC power source using an everyday tactile button. The breakout uses a latching analog circuit that is triggered by a push of the button. Press once to turn on, then press again to turn off. The circuit uses a 3A P-FET to connect and disconnect the IN pin to the OUT pin. Works great from 3V to 14VDC and up to 3A (although the FET gets a little toasty at continuous 3A draw) yet has only 0.5uA quiescent current draw.

Using it is easy: connect the power source to Ground and IN, then the load from Ground to OUT. We include a 12mm tactile switch that works well but you can solder in your own switch as well. Press the button (or short the button pins) to alternate between on or off. A on-board red LED will light up when active so you know its working. There's a fourth KILL pin, which you can use to turn off the load and/or keep it off even if the button is pressed. When 1 or more volts is applied it will instantly turn off the FET. This allows your project to turn itself off.

Comes with a assembled & tested bread-board friendly breakout board with four mounting holes, a 12mm tactile button, and some 0.1" male header you can solder to the board to plug it into a breadboard.

The power switch is an elegant way to control power to your project, but there are some things to keep in mind: since there is a pass FET, this is only for 3-14V DC voltages. This is not a mechanical switch so there is no air-gap isolation. There is a 'body diode' in the pass FET so if the load has a voltage on it that is higher than the input voltage, current will flow back to the input. There is built-in debouncing but very bouncy switches can be annoying as they will turn on and off fast instead of latching.

Voor meer info klik hier

Sorteren op:

Review toevoegen

Geen reviews gevonden.

Stel een vraag over dit product

Velden met een * zijn verplicht om in te vullen.

Jouw vraag is verzonden! Bedankt.

We zullen jou zo snel mogelijk voorzien van een antwoord.